How To Adjust Rear Derailleur On Mountain Bike?

Similarly, How do you adjust rear gears on a mountain bike?

Step behind the bike and inspect how the chain rides on the sprocket by shifting down to the lowest gear. Tighten the L-screw clockwise until it is centered on the sprocket if it seems to be riding into the spokes. If it seems to be shifting down, loosen the screw until it aligns.

Also, it is asked, How do I adjust my Rd?

Adjust the cable tension as needed. The tension is reduced as you go clockwise, bringing it closer to the frame. Increase the cable tension by rotating the barrel adjuster anticlockwise if the chain is slow to move higher. If it skips a gear, reduce the tension by turning the adjuster clockwise.

Secondly, What are the three screws on a rear derailleur?

There are three limit screws on most derailleurs: upper limit, lower limit, and B-limit. In high gears, the upper limit screw determines how far the derailleur may shift. In lower gears, the lower limit screw determines the maximum distance the derailleur may shift.

Also, How do you adjust Shimano mountain bike gears?

Make that the little barrel adjuster or circular knob connected to the cable is adjusted. Turn it in a clockwise direction to allow for future changes if necessary. The upper screw is the high limit, and it is often located across the barrel adjuster. It’s preferable to spin it using a screwdriver.

People also ask, Why is my derailleur touching my cassette?

When the bike is upside down, most derailleurs will drag on the top gear of a 34 t cassette, but not when it is right-side up. Shorten the cable loop on the derailleur if it does it while it’s right side up. It is not a good idea to shorten the housing loop. The b-tension screw should be adjusted.

This Video Should Help:

The “rear derailleur adjustment screws” is a tool that allows you to adjust the rear derailleur on your mountain bike.

Related Tags

  • how to adjust front derailleur on mountain bike
  • shimano rear derailleur installation instructions
  • rear derailleur tension problem
  • rear derailleur won’t shift to highest gear
  • mountain bike derailleur

Related Questions and Answers

How much does it cost to adjust a derailleur?

Derailleurs – $25 labor for derailleur adjustment and lubrication (per derailleur). Labor is $25 plus the cost of the cable and housing if the cable and housing need to be replaced. There is an extra $15-20 labor fee if a bent derailleur has to be adjusted.

What does a barrel adjuster do on a bike?

Small cups with a hole in the bottom that are fitted into various spots around your bike are known as barrel adjusters. Your brake levers, brake calipers, gear levers, and derailleurs are normally where you’ll find them. They function by extending the distance that an inner cable may travel.

How To Adjust Rear Derailleur On Mountain Bike

How do you use Shimano 7-speed gears?

If you want to change gear with a conventional Shimano 7-speed shifter, you’ll need to push the primary shifter with your finger while riding forwards every time you want to go down a gear. To move to a higher gear, push the opposite shifter (which is usually a bit smaller) with your finger.

How tight should the rear derailleur cable be?

Make sure the derailleur mounting bolt is snug; otherwise, no matter how nicely the cable is fitted, shifting will be clumsy. A 5-millimeter hex wrench is normally required for this. If you can’t discover the precise specification, this bolt’s normal torque range is 5 to 8Nm.

What gear combination is best for going uphill?

Low Gear = Easy = Good for Climbing: Your bike’s “low” gear is the front chain ring with the lowest cog and the biggest cog on the cassette (rear gears). The pedaling will be the simplest in this position, and you’ll be able to bike uphill with the least amount of resistance.

Do you shift gears while pedaling?

While standing motionless, shifting gears bends the wires and puts pressure on the derailleurs. Remember that the bike will only change gears if you are pedaling.

Why does my mountain bike chain click when I’m riding it?

When your chain wants to hop up or down a gear on the rear cassette, it makes a clicking noise. The tension of the wire that leads from your shifter to your rear derailleur can usually be adjusted to correct this.


The “how to adjust shimano rear derailleur on a mountain bike” is a question about how to adjust the rear derailleur on a mountain bike. This process can be done without tools, and it will help prevent your chain from getting stuck in the gears.

+ posts